The smart control a heat pump actually needs.
A heat pump is only as good as the control that runs it. Left on a simple on/off room thermostat — the kind that suited a gas boiler — a heat pump is forced to blast hot then cut out, which is exactly how it runs least efficiently. Homely is a UK smart controller built specifically for air-source heat pumps: it learns how your home heats, follows the weather forecast to modulate the flow temperature, and shifts heating and hot water into your cheapest tariff hours — all automatically. It works across most major heat-pump brands, retrofits to systems you already have, and is set up by your installer in under 45 minutes. On this page we explain why heat pumps need weather- and load-compensating controls rather than a basic thermostat, what Homely does, the brands it works with, and an honest view of where it fits and where it doesn’t.
Built for heat pumps
Not a repurposed boiler thermostat — Homely is designed to run a heat pump “low and slow” for the efficiency it’s capable of.
Weather-compensating
It reads the weather forecast and continuously adjusts flow temperature — the key to steady comfort and low running costs.
Tariff-smart savings
Shifts heating and hot water into cheap off-peak hours on time-of-use tariffs — independent testing shows up to 31% off heating bills.
Retrofit & app-controlled
Fits an existing heat pump in under 45 minutes, then set-and-forget from the Homely app on iOS or Android.
Why a heat pump needs a smart control.
A gas boiler makes fierce heat on demand, so an on/off thermostat suits it: call for heat, fire up to 70°C, stop. A heat pump works the opposite way. It’s most efficient when it runs gently and continuously at a low flow temperature — “low and slow” — keeping the home at a steady temperature rather than blasting and cutting out.
To do that well, a heat pump needs weather compensation and load compensation: the control constantly nudges the flow temperature up a little when it’s colder outside and eases it down when it’s milder, matching output to the home’s real heat loss. A basic thermostat can’t do this — and manufacturer weather-compensation curves are often left roughly set at install and rarely tuned again.
Homely automates all of it. It learns your home’s thermal behaviour, follows the weather forecast, and — on a time-of-use tariff — times heating and hot water for the cheapest hours, finding the balance between comfort, efficiency and cost.
In short: the control does as much for your bills as the heat pump itself — and Homely is a leading heat-pump-specific example.

Blasts hot then cuts out, fixed curve, ignores tariffs — how a heat pump runs least efficiently.

Low-and-slow, weather-responsive flow temperature, off-peak tariff timing.
The benefits that matter in a real home.
- Lower running costs, automatically. Homely runs the heat pump “low and slow” and, on a time-of-use tariff, times heating and hot water for cheap hours — independent testing shows up to 31% off heating bills.
- Set-and-forget comfort. You choose the temperature you want; Homely learns your home and holds it steady without the constant tinkering heat-pump ownership can otherwise involve.
- Weather-responsive by default. It follows the forecast to modulate flow temperature — no fiddly compensation curves for you or your installer to hand-tune.
- Works with the brand you’re fitting. Compatible with most major heat-pump makers, so it slots into the system your installer recommends rather than dictating it.
- Retrofit-friendly and quick. Added during a new install or to an existing heat pump in under 45 minutes, then controlled from the Homely app.
Homely at a glance
Independently recognised.
Homely’s credentials are practical: broad manufacturer compatibility, integration with the UK’s leading smart tariffs, and independent evidence of the savings it delivers.
What Homely does, in three parts.
Homely isn’t a heat pump — it’s the intelligence that runs one well. Here’s the hub, the app and the two ways it saves you money, the way our installers set it up.
Homely controls the heat pump only — any additional valves or pumps must be driven by the heat pump itself. It needs WiFi (or a phone hotspot) and is not compatible with hybrid or cascade systems. Smart mode is free; Smart+ (£25 a year at time of writing) unlocks fuller time-of-use optimisation and best suits homes on a multi-rate tariff. Details and savings figures are Homely’s own and vary by home.
Homely up close.
The hub, the intelligence and the app that ties it together — flick through to see how it works.
Compatible with the heat pump you’re fitting.
Homely is designed to work across most major air-source heat-pump makers — so it fits the system your installer recommends. This is the current list; because it changes (Mitsubishi was added recently), your installer will confirm your exact model.
| Heat-pump brand | Works with Homely | Good to know |
|---|---|---|
| Daikin | Yes | Needs a DCOM Modbus adaptor · single-zone |
| Mitsubishi Ecodan | Yes (new) | MelcoBEMS Mini A1M adaptor · FTC5–7 · single-zone |
| Samsung | Yes | MIM-B19N adaptor · post-2015 AE models |
| Grant | Yes | Units made after March 2021 · single-zone |
| Worcester Bosch | Yes | CS2000 air-to-water models |
| Ideal Heating | Yes | HP290 range |
| LG | Yes | Gen 3/4 units · Siemens Modbus · single-zone |
| Others | Yes | Airwell, Clivet, Ebac, Midea, Nordis, Riello, Trianco |
Model-specific: some brands need a paid Modbus adaptor and several are single-zone only. Homely is not compatible with hybrid or cascade systems. Always check the current compatibility list or ask your installer for your exact heat-pump model.
Homely vs the alternatives.
No control is right for everyone. Here’s an honest, like-for-like look at how a heat-pump-specific smart control compares with the options most homeowners weigh up.
| Homely (smart HP control) | Basic smart thermostat (Nest, Hive, etc.) | Manufacturer’s own control (built-in weather comp) | |
|---|---|---|---|
| Designed for heat pumps | Yes — purpose-built | No — boiler-first on/off | Yes — brand-specific |
| Weather compensation | Automatic, forecast-led | Rarely, or basic | Yes, but often left un-tuned |
| Time-of-use tariff timing | Yes — Smart+ mode | Limited | Usually not |
| Self-learning | Yes | Some | No |
| Cross-brand | Most major HP brands | Broad, but generic | Locked to that brand |
| Best for | Lowest bills & hands-off comfort | Simple room control | Staying in one ecosystem |
Is Homely right for you?.
We’re a comparison service, not a manufacturer — so here’s the full picture. Homely is a strong pick for most heat-pump homes, with a few things worth knowing.
Why homeowners choose Homely
- Real, tested savings. Independent testing shows up to 31% off heating bills on a time-of-use tariff — because it runs the heat pump the efficient way and times it for cheap power.
- Genuinely hands-off. It learns your home and holds a steady temperature, taking away the tinkering some heat-pump owners dread.
- Works with your brand. Compatible with most major heat-pump makers, so it fits the system your installer recommends.
- Quick and retrofittable. Fitted in under 45 minutes to a new or existing heat pump, then controlled from a simple app.
Things to weigh up
- Compatibility is model-specific. Some brands need a paid Modbus adaptor, several are single-zone only, and it doesn’t work with hybrid or cascade systems — check your exact model.
- The biggest savings need a smart tariff. The headline figures rely on a time-of-use tariff and the £25-a-year Smart+ mode; on a single flat rate the gains are smaller.
- It needs WiFi. Homely relies on a home WiFi connection (or a phone hotspot) to run and update.
- Savings vary by home. The “up to” figures are Homely’s own and depend on your property, tariff and how you heat — treat them as a guide, not a promise.
Homely control FAQ.
What is Homely, and how is it different from a normal thermostat?
Homely is a smart controller built specifically for air-source heat pumps. A normal thermostat simply switches heating on and off, which suits a boiler but makes a heat pump run inefficiently. Homely instead runs the heat pump “low and slow”, adjusting the flow temperature to the weather and timing heating for cheaper tariff hours — automatically.
Why does a heat pump need weather and load compensation?
Heat pumps are most efficient at low, steady flow temperatures. Weather and load compensation nudge that flow temperature up when it’s colder outside and down when it’s milder, matching the heat pump’s output to your home’s real heat loss. Get this right and running costs fall; leave a heat pump on a basic on/off thermostat and it wastes energy cycling hard.
How much could Homely save me?
Independent testing cited by Homely shows up to 31% off heating bills, and a Homely case study cites up to £444 a year, when paired with a time-of-use tariff and the Smart+ mode. These are “up to” figures and depend heavily on your home, tariff and habits — treat them as a guide rather than a guarantee.
Will Homely work with my heat pump?
Homely works with most major heat-pump brands — including Daikin, Mitsubishi, Samsung, Grant, Worcester Bosch, Ideal, LG, Midea and more. Some brands need a Modbus adaptor and several are single-zone only, and it isn’t compatible with hybrid or cascade systems. Your installer will confirm compatibility for your exact model.
Can Homely be added to a heat pump I already have?
Yes. Homely is retrofit-friendly — a registered installer can add it to an existing compatible heat pump, typically in under 45 minutes, as well as fitting it during a new installation.
Is there a subscription?
Homely’s Smart mode is free and best suits homes on a single-rate tariff. Smart+ (£25 a year at time of writing) adds fuller time-of-use optimisation and suits homes on a multi-rate or off-peak tariff, where it can unlock the larger savings.
Do I need anything else for it to work?
Homely needs a home WiFi connection (or a second device acting as a hotspot) and the Homely app on iOS or Android. To get the most from it, a time-of-use electricity tariff — such as those from Octopus, EDF, E.ON Next or British Gas — lets it schedule heating for the cheapest hours.
Getting Homely onto your heat pump.
Energy Saving Hub matches you with MCS-accredited independent installers who fit heat pumps and can add Homely — so you get competitive quotes without the hard sell.
Tell us about your home
Answer a few quick questions about your property and heating — it takes about a minute.
Get matched to installers
We connect you with trusted independent partners in your area who install heat pumps and fit Homely.
Compare and decide
Receive tailored quotes, compare options at your own pace, and choose what’s right for you.
Like the sound of Homely?
Get free, no-obligation quotes from independent MCS-accredited installers who fit heat pumps and Homely near you.
Helpful guides to plan your heat pump.
Want the full compatibility list, the app and the technical detail?
See the full Homely compatibility list at homelyenergy.com →Homely is a smart controller used with an air-source heat pump; specifications, compatible models, subscription pricing and savings figures shown here are taken from Homely’s official website and are indicative — exact compatibility, adaptor requirements, pricing and savings vary by heat-pump model, tariff and home, and change over time, so confirm current details with your installer. Independent savings figures (“up to 31%” / “up to £444 a year”) are cited by Homely and depend on a time-of-use tariff and the Smart+ mode. Energy Saving Hub introduces homeowners to independent, MCS-accredited installers and does not carry out installations directly.















